潛水渣漿泵作業注意事項

潛水渣漿泵工作時，潛水泥砂泵需要放在陸地上，吸水管放在水中，還需要灌泵啟動。泥漿泵和液下渣漿泵由于受到結構的限制，工作時電機需要放在水面之上，潛水吸沙泵放入水中，因此必須固定，否則，電機掉到水中會導致電機報廢。而且由于長軸長度一般固定，所以耐磨潛水渣漿泵安裝使用較麻煩，應用的場合受到很多的限制。如果有備用泵，好兩臺泵輪流使用。如果卡泵就只有修泵了，可以在進水口加一張網，不讓過多的雜質進到泵里，這樣卡泵的機率就會小很多！

潛水吸砂泵 潛水吸沙泵 潛水泥漿泵 潛水礦漿泵 潛水尾礦泵

潛水吸砂泵 潛水吸沙泵 潛水泥漿泵 潛水礦漿泵 潛水尾礦泵

渣漿泵生產廠家，主要產品有渣漿泵、脫硫泵、砂礫泵、泥漿泵、雜質泵、污水泵、泡沫泵、雙吸泵等渣漿泵配件及渣漿泵成套產品。

一般雜質泵的葉輪用平行蓋板，漿體進入葉輪后，在出口處向兩側形成外旋渦，使葉輪的前后蓋板和內襯嚴重磨損，這是造成過流部件壽命短的主要原因，而ZJA系列渣漿泵充分吸收了ZJ系列渣漿泵和沃曼泵的優點，設計的葉輪在出口處形成凹形，使葉輪兩側前后蓋板處的速度大于中間速度，漿體在出口處分為兩股流體，向中心旋轉，迫使顆粒向中心流動造成內旋渦狀，使兩側的濃度降低，從而減輕了泵體流道和兩側壁的磨損。Submersible slurry pump operation matters needing attention submersible slurry pump work, submersible cement sand pump needs to be put on the land, suction pipe in the water, but also need to start the pump. Because of the structure limitation of the mud pump and the slurry pump, the motor needs to be put on the water surface when they work, and the sand suction pump for diving must be fixed, otherwise, the motor will be discarded when it falls into the water. And because the length of the long shaft is generally fixed, so wear-resistant submersible slurry pump installation and use more trouble, application of the occasion by a lot of restrictions. If there is a backup pump, good two pumps in turn use. If the card pump only repair the pump, you can add a net in the inlet, do not let too many impurities into the pump, so the card pump will be much less! Submersible sand pump, submersible sand pump, submersible slurry pump, submersible mineral slurry pump, submersible tailings pump sand pump, submersible sand pump, submersible slurry pump, submersible slurry pump, submersible tailings pump slurry pump, submersible slurry pump, slurry pump manufacturers, the main products are slurry pump, desulphurization pump, gravel pump, slurry pump, impurity pump, sewage pump, foam pump, double suction pump and other slurry pump accessories and slurry pump complete sets of products. Generally, the impellers of the impellers of the impellers use parallel cover plates. After the slurry enters the impellers, it forms outer vortices to both sides at the outlet, which causes the front and rear cover plates and the inner lining of the impellers to wear seriously. This is the main reason for the short service life of the overflow parts, while Zja series slurry pumps fully absorb the advantages of ZJ series slurry pumps and Wurman pumps, the designed impeller is concave at the outlet, which makes the speed at the front and rear cover plates on both sides of the impeller greater than the middle speed, and the slurry is divided into two fluids at the outlet, rotating toward the center forces the particles to flow toward the center to create an inner vortex, which reduces the concentration on both sides, thus reducing the flow channel and the wear of both sides of the pump body.